Press operation essentials required to check the various parts of the filling oil components are tightened, the operating handle, the flapper is flexible moving large pulley by hand to check the machine for loose or stuck phenomenon. If abnormal loosen and remove the lock nut, the pressing screw shaft screwed into a dead point, and then return 3-4 laps, then a half circle forward, in order to maintain the gap pressing screw with a cake circle. Adjust the belt tension. Dial material rotating shaft drive pulley sheaves is a bivalent, if available slag serious small sheave. Open the electrical box door, the air inside the power switch in the closing position, start the motor, check the trough wheel rotation direction is consistent with the direction indicated. Adjusting the temperature control device: press the desired temperature is adjusted to 150-200. C (based on fuel availability). Turn the heat switch to the host machine screw press heated up sales, then the temperature controller on the bright green light, red light is off, when the engine temperature rises to a set temperature, the red light, green light goes out. The temperature of the machine is automatically controlled and maintained at a set temperature 150-200. C, when the low winter temperatures, the oil pan heating switch is turned on, the oil pan temperature, facilitate oil flow. After feeding should be turned slowly and evenly, not too fast and start feeding more or less time, or it may cause blockage and stuck bore pressing and other machinery accidents. Start feeding the cake should be thicker, the normal of the cake, machine temperature reaches 150-200. C before it will be expected to press for normal embryos into the hopper. The normal operation of the machine observe the cake case, as no cake can be pressed again to exit l screw a 2 laps, as not a cake, you should stop to check, remember to prevent backsliding. Hand moving large pulley, reversing laps on again. Troubleshooting and then be pressed. L during normal operation of a 2 mm thick cake, and a tile-like, pinching sticky, wrinkled outer surface with no traces of oil. When press idle, the motor current should be around 3A. As the current is too high, they should immediately stop checks, adjustments and then boot. And moisture control blanks are neither too high nor too low. Normally the cake should flaky, by pressing screw shaft side smooth, the other side has a lot hair pattern. As the cake loose weakness, or the cake shapeless, darker color, hand pinch Serve fragments, indicating little billet add water; if the cake soft, flaky larger increase, or the oil bubble, Minga said that too much water. Under normal circumstances, no residue or very little between rounds slag discharge, discharge of the slag in the article, such as a description of the slag was fine flake more water, the less water then the powder residue. Press the correct installation. After the press load properly, prepare about 50kg rapeseed or soybeans, ready to put into the hopper. Note: When you press the feed can not start too fast, otherwise the sudden increase pressure inside the chamber pressing, pressing screw shaft rotation does not move, causing blockage virgin bore, and even squeeze cage fracture, a major accident. So at the beginning of compression, the feed should be evenly slowly put into the hopper, so press were running together. Before installation, respond to press newly purchased thorough cleaning. Out of the spindle, lifted the squeeze cage, with emery cloth pressing screw outer surface, an inner surface and screw feeder and polished smooth. All lubrication lubrication, gearbox oil added screw press equipment, its varieties and grades shall comply with the instructions. After sanding smooth circular rows, when installed must be arranged according to the original position screw press fitting, screw press can not be misplaced, because round row arrangement position and order of performance for oil extraction great relationship. After the round row installed with compression nut pressing, pressing oil extraction extent to which the disk can squirm when appropriate. After the above press treatment, it can be fixed with anchor bolts on the foundation. During installation, the motor pulley and press the pulley should align moderate position, the rotational direction is correct, the tightness of the belt should be adjusted appropriately. Screw press sales | screw press | [press] selected Goodwin quality assurance provided by the Nanyang City, Qi Feng Machinery Co., Ltd. Nanyang City, Qi Feng Machinery Co., Ltd. (www.qifengjixie.com) (www.nyqfjx.com) strong, credible, Nanyang in Henan edible oil processing machinery industry has accumulated a large number of loyal customers. The company better work attitude and constantly improving innovative ideas will lead Goodwin machinery into the brilliant and you work for a better future!